NRP-192PRi    PoE Extenders    www.nsgate.ru
NSGate. Be Sure.


Solutions and Applications
Outdoor access Nodes NSBox
Enclosures NSB-xxx
Accessories NSBon-xx
PoE Industrial Switches
PoE Injectors
PoE Extenders
Industrial SFP modules
Din-Rail Power Supplies


Ethernet over PDH/SDH
Ethernet over xDSL
Our new products

Explosion-proof enclosures
NSBox-4042E  Explosion-proof

PoE Extender NRP-172PRi
NRP-172PRi Extender | The best

NSBox Heating
NSBox Heating  for enclosure
NRP-192PRi  Ultra PoE Extender     Built-In Voltage Booster
3 Ethernet 10/100/1000Base-T + Ultra PoE 95W/60W/30W + VDC Booster
Brief
  › Gigabit Ethernet
  › 95W_60W_30W_15W PoE
  › Built-in Voltage Booster
  › Waterproof RJ45 connectors

  PoE Extender PoE Repeater NRP-192PRi The Gigabit Ultra PoE Extender, Model NRP-192PRi, is devised to extend connection distances from a PSE (Power Source Equipment) to a PD (Powered Device) another 100 m via Cat5e or Cat6 cable.
  The transmission is carried out at a distance of 200 to 500 meters or more by cascading these extenders to a daisy chain. The built-in booster compensates for the voltage drop (48VDC) on the twisted pair with the cascade connection. Similar repeaters of other manufacturers do not have this characteristic, so the use of more than two such repeaters in the chain is impossible. Device doesn't need any additional power supply, because it uses a transit PoE from the input cable, while its power consumption does not exceed 3 watts. PoE Extender usually works with any PSE or PD devices. This solves the problem of "only 100 m for PoE and data" and there is a possibility to install IP equipment (IP Cameras, IP Access Controls, and Wireless Access Points) in the places most suitable for this.
  The advantages of NRP-192PRi over other existing analogues:
    Support for Gigabit Ethernet 10/100/1000-BaseT;
    Two output PSE ports 75W/60W/30W/15W instead of one in other devices;
    The input PD port works with power supplies from 30 to 95W;
    Voltage drop compensation on twisted pair (built-in Voltage Booster);
    The industrial grade device with wide operating temperature range;
    The rugged weatherproof housing with waterproof RJ45 connectors.
  The devices are easy to install and operate in Plug & Play mode. The housing has three waterproof RJ45 connectors for one input port and two output ports. The input port is connected to the PSE equipment (PoE Injector or PoE Switch) and the output ports to the equipment PD (IP Cameras, IP Access Controls, and Wireless Access Points) or to the next extender during cascading multiple PoE extenders.


Technical Data:
3 ports Ethernet 10/100/1000Base-T with supporting Ultra PoE 95W/60W
Switch Fabric 6Gbps, Jumbo Frame 10Kb, 8K MAC, 1Mb buffer
Complies with IEEE 802.3/802.3u/802.3ab/802.3x Flow Control Back-pressure
Support 10/100/1000 auto-negotiation and auto-MDIX
Extends an existing PoE connection beyond the 100m (328-ft.) limit
It is possible to cascade 4 devices into a chain up to 500 m
Compensation of voltage drop in the chain (built-in Booster)
1 port PD IN up to 95W + 2 ports PSE OUT 75W/60W/30W/15W
POE Pin Assignment: 1/2(+), 3/6(-) and 4/5(+), 7/8(-)
Power Consumption: 3W, Does not require an additional power supply
Overload current and reverse polarity protection
Housing IP65/IK10, Wall mounting, Waterproof RJ45 connectors
Operating Temperature: -40 to +75C; Dimensions: 190x85x65mm; MTBF > 500000hrs

 The number of Extenders in the chain and Maximum wattage of the PoE port (PSE OUT)
when NRP-192PRi is connected using only one output port
PoE (PD IN)1 (100-200m)2 (200-300m)3 (300-400m)4 (400-500m)
95W65W46W35W29W
60W47W34W27W22W
30W22W16W10W -

PoE Extender PoE Repeater NRP-192PRi

Ordering Information
ModelsPart NumberFeatures  
NRP-192PRi63P2G9EIExtender: 3 Ethernet 10/100/1000T Ultra PoE 95W/60W/30W, Booster, 1PD/2PSE